| Specifications |
ConnectCore™ 9P 9215 |
| Hardware |
| Processor Type |
32-bit NS9215 processor |
| ARM Core |
ARM926EJ-S |
| Cache |
4k I-Cache/4k D-Cache |
| Processor Speed |
150 MHz |
| Memory Base Population |
Up to 16 MB NOR flash
Up to 32 MB SDRAM |
| Additional Population Options |
RJ-45 Ethernet connector
2 / 4 / 8 / 16 MB NOR flash
8 / 16 / 32 MB SDRAM |
| Flexible Interface Modules (FIMs) |
2 x 300 MHz DRPIC165X CPUs with 2k program/192 bytes data RAM |
| On-chip 256-bit AES Accelerator |
• |
| Power Management Modes |
On-the-fly clock scaling; Low-power sleep modes; Configurable scaling/wake-up events (RTC, ADC, EIRQ, UART, etc.) |
| Pins/Form Factor |
Small-footprint module with 2 x 80-pin board-to-board connectors |
| UART |
Up to 4 high-speed UARTs; Maximum data rate 1.8432 Mbps |
| GPIO |
Up to 64 GPIOs; 2 external IRQs |
| SPI |
Master data rate 33.3 Mbps; Slave data rate 7.5 Mbps |
| I2C |
v1.0 bus interface; 7-bit and 10-bit address modes |
| External Memory Bus |
17-bit address and 16-bit data bus with 2 external chip select |
| ADC |
12-bit/8-channel; External reference |
| Timers/PWM |
Up to ten 16-/32-bit timers/counters
Modes: internal timer with external terminal count option, external gated timer, event counter
Up to 5 PWM functions |
| LEDs |
2 (general purpose) |
| POR controller |
• |
| Watchdog Timer (16-bit) |
• |
| Real-Time Clock |
With 64 bytes of NVRAM and external battery backup |
| JTAG interface |
• |
| Quadrature Decoder/Counter |
• |
| 5V Tolerant General Purpose and Memory Inputs |
• |
| Dimensions (L x W x H) |
1.97 in (50 mm) x 1.97 in (50 mm) x 6.1 mm
(population option w/o RJ-45) |
| Network Interface - Wired |
| Standard |
IEEE 802.3 |
| Physical Layer |
10/100Base-T |
| Data Rate |
10/100 Mbps (auto-sensing) |
| Mode |
Full or half duplex (auto-sensing) |
|
| Environmental |
| Operating Temperature |
-40° C to +85°C |
| Storage Temperature |
-50° C to 125° C (-58° F to 257 °F) |
| Relative Humidity |
5% to 95% (non-condensing) |
| Altitude |
12,000 feet (3,658 meters) |
| Power Requirements (3.3V) |
| Maximum |
554 mA (1.83 W) |
| Typical |
443 mA (1.46 W);
UART B/D and Ethernet on |
| Idle |
208 mA (686 mW);
/16 clock scaling, Ethernet on |
| Sleep |
46 mA (151 mW);
EIRQ wake-up, Ethernet PHY off |
| Regulatory Approvals |
| FCC Part 15 Class B, EN 55022 Class B |
• |
| EN 61000-3-2 and EN 61000-3-3 |
• |
| ICES-003 Class B, VCCI Class II, AS 3548 |
• |
| FCC Part 15 Sub C Section 15.247 |
• |
| IC RSS-210 Issue 5 Section 6.2.2(o) |
• |
| EN 300 328, EN 301 489-17 |
• |
| UL 60950-1, EN 60950 (EU) |
• |
| CSA C22.2, No. 60950 |
• |
| EN 55024 |
• |
| Japan |
Regulatory approvals pending |
ConnectCore 9P 9215 Digi JumpStart Kit for NET+OS 7 w/Eclipse-based Digi ESP IDE, USB debugger, installation and setup support package
ConnectCore 9P 9215 Digi JumpStart Kit for .NET Micro Framework 2.5, including Visual Studio 2005 (90-day trial license)